Anonymous wrote:
im looking into buying one of these massive devices, but i cant seem to find any good places online with pricing information. where might i go to look into buying one here in the US? and about how much do you think it would cost?
98 THERMWOOD 67 .... OFFER REQUESTED
original asking price $79k
MY OFFER (subject to inspection) $______________
1998 Thermwood
> CNC; Model 67 Single 5'x10' deep moving table, 36"Z axis 1500 inch per
minute
> maximum feed speed, Engineered steel construction, track ways, AC servos,
> ball screw drives, Machine enclosure and dual end variable speed spindle,
> Automatic Tool Length Measurement, Automatic Tool Changer. 460 V. 240 KVA;
Nema
> Interrupt Rating 35 A; Full Load Motor 12.5 A.; 2000 approximate hours on
> floorpanels - no metal.
> It
----------------------------------------------------------------------------------------------------------------------
MY OFFER (subject to inspection) $______________
THERMWOOD 40
Thermwood CNC Router was purchased new in 2000 and was only used for 1 year. The unit is under power and can be inspected prior to final payment. The specs are as follows:
Thermwood C-40 3 Axis Router
Year Built 2000
Programmable and controlled three-axis motion.
*High performance AC Brushless Servo Drive System with feed speeds to 1500 inches/minute.
*6" vertical motion (Z axis).
*Series 91000 SuperControl.
*Solid-state memory and control system, fully diagnostic.
*6.4 Gigabyte hard disk system for program and system storage.
*3-1/2", 1.4 floppy disk drive.
*14" color monitor.
*85 key, 101 key emulation keyboard.
*EIA 274D programming.
*Feed rate override.
*Feed hold.
*Menu driven programming.
ADDITIONAL OPTIONAL EQUIPMENT INCLUDED:
*480 Volt, 60 Hz, 3 Phase power input with optional 220 Volt.
*7 1/4" Gantry Spacer, allows 10 1/2 inches of clearance and Z travel.
*Automatic Tool Length Sensing.
*Networking OS/2. Includes a 3Com 16-bit combo card, OS/2 Warp Connect and operating instructions. Compatible with Microsoft or Novell.
*Portable Hand Held Programming Unit equipped with keyboard and hand wheel/pulse generator. Provides full programming, lines, arcs, speed control and editing. Programming features can be performed at the control system.
CONDITION:
*Like new - very low usage hours - only operated one year.
-------------------------------------------------------------------------------------------------------------------------
was $79,900 MY OFFER (subject to inspection) $______________
MULTICAM "MT 510" CNC Router w/ATC. 15' x 10' Worktable, 10 HP router, 8-pos. ATC, 30 HP vac. pump.
2002 - Excellent Cond
-----------------------------------------------------------------------------------------------------------------------
MY OFFER (subject to inspection) $______________
KOMO
VR 2005 TT MACH III 2000 South Special Twin 5 x 10 tables, 4 routers, 48 position ATC, save $136,000!
----------------------------------------------------------------------------------------------------------------------
$18,900 .....MY OFFER (subject to inspection) $______________
Specifications: 2000
Techno Isel 3-axis servo CNC Router system.
Includes servo controller and servo automation software
Machine stand with cable carriers
3D linear and 2 axis circular tool path capability
double linear recirculating ball bearing blocks on each axis
Servo relay box with a switched outlet can be turned on or off from within the program
GCODE interface for servo controllers
MASTERCAM version 8.1 Router software. Version 9 will be included with the machine.
New replacement table included
This machine has been used for engraving and it well maintained
Table Configuration:
43.3" x 21.2" Table surface
(5) machined t-slots on 50 mm centers in table for fixturing plates
Model 040 vacuum table with (3) zone manual manifold
Vacuum pump is not included
Head Configuration:
3.25 HP PORTER CABLE Router (10,000, 13,000, 16,000, 19,000, and 22,000 RPM spindle speeds)
Collet wrench is included
Positioning Speeds:
Axis are positioned by ball screw with anti backlash ball nuts
X-axis positioning speeds of 250 IPM
Y-axis positioning speeds of 250 IPM
Maximum programmable cutting speed of 200 IPM
X and Y axis travel is 29.5" x 21.2"
Z axis travel is 6.8"
-----------------------------------------------------------------------------------------------------------------------
asking $16,900 MY OFFER (subject to inspection) $______________
97 Camtech Routermaster II 52 X 102 cnc router table with 5hp perski
spindle, tool path software. Low hours purchased as a hobby, training
aval. only cut only uhmw and mdf with machine.software on the control is CamTech CamPath witch read tool path and"G" code programs. Very easy machine to program and operate. This machine was special ordered with 5.75 "Z" axis travel with heavy duty gantry
column.Everything in mint condition.
this machine was a special order to my spec's. Paid $35,000.00 used very little in afternoons after work the first year, then used it for signs for friends and family maybe twice a year, it is now paid for with no leans.
---------------------------------------------------------------------------------------------------------------------
avail soon:
MY OFFER (subject to inspection) $______________
Biesse Arrow TCR, built in 2000. Two spindles ~12hp or so, ATC with 10 tools per head, Biesse 19 drill boring head, 13 vertical, 6 horizontal 8+5 config. C-axis on spindle #1. Twin tables, each 63" x 63", max work area of 127" x 63" to get a 1/2" tool all the way around. 12" vertical travel, HSK63-F spindle connect. Acculube micro drop cutter lube on both spindles, NC controlled. 16 pods for elevated work. Aggregate stop collar for spindle #2. 25HP Travini liquid ring Vac. Osai 10 controller. I Might be able to arrange factory installation at new owners site.
------------------------------------------------------------------------------------------------------------------------
MY OFFER (subject to inspection) $______________
KOMO VR2110 TT LARGE TABLE CNC ROUTER/ SEE HEADS IN SPECS
1996 KOMO ..." VR 2010 TT" TWIN TABLE CNC ROUTER
Elect./Voltage: 220 V, 60 Cy, 3 Ph.
Description: 2-Head Twin Table Router; (2) 120" x 120" tables which can function independently or be locked together for 10' x 20' table.
• Equipped with: (2) 12 HP Main motors, heads have programmable spindle speeds up to 18,000 RPM and quick change spindles with "BT 40" taper.
• X- & Y-Axis rapid traverse is 1,000 IPM, Z-axis rapid traverse is 600 IPM; X-axis programmable travel is 231", Y-axis is 129", Z-axis travel is 42" and clearance under the bridge is 52".
• Complete with: FANUC "16M" Series computer control system featuring (3) axes simultaneous control, RS-232 port, hand held manual pulse generator for accuracy of work coordinate setups, feed rate & spindle speed override.
• Includes 25 HP QUINCY Rotary vacuum system (357/29/240 V
Login
Register
FAQ
Search
